For AI agents: the complete documentation index is available at https://docs.ovhcloud.com/de/llms.txt, the full documentation bundle is available at https://docs.ovhcloud.com/de/llms-full.txt, and this page is available as Markdown at https://docs.ovhcloud.com/de/guides/bare-metal-cloud/dedicated-servers/efi-system-partition.md.

Understanding the EFI System Partition on dedicated servers

Als Markdown ansehen

Find out how the EFI System Partition (ESP) is laid out on a multi-disk dedicated server and which operating systems put it on software RAID1

Objective

Info

This guide only applies to servers that boot in UEFI mode. A server that boots in legacy (BIOS) mode has no ESP.

Info

An installation on a single disk or on a hardware RAID volume has a single ESP, so neither layout described here applies to it.

On a server that boots in UEFI mode, the EFI System Partition (ESP) holds the bootloader of the operating system (e.g. GRUB or systemd-boot). When an operating system is installed on several disks with software RAID, every disk gets an ESP, so that the server can still boot when one of the disks fails.

Depending on the operating system, the installation either creates one independent ESP per disk, or a single ESP on top of a software RAID1 array that spans all the installation disks.

This guide explains the two layouts, lists the operating systems that use each of them, and describes what the RAID1 layout changes for you.

Requirements

  • A dedicated server that boots in UEFI mode
  • A Linux operating system installed by OVHcloud on two disks or more, with software RAID

Instructions

How the server boots from the ESP

OVHcloud dedicated servers boot from the network. When the server is set to boot to disk, iPXE starts the bootloader found in the ESP of one of the disks, at the path set during the OS installation. If that fails, it falls back to rEFInd, which looks for a bootloader on every disk. See Understanding the dedicated server boot process for the whole sequence.

Since the server can start the bootloader from any disk, every ESP must hold the same up-to-date files.

One ESP per disk

This layout is mostly used by older Linux operating systems (see Availability by operating system). Each disk has its own ESP, and only one of them is mounted on /boot/efi. At the end of the installation, the contents of the mounted ESP are copied once to the other disks' ESPs; later bootloader updates write only to the mounted ESP.

If the server starts the bootloader from a disk whose ESP is out of date, it runs an outdated bootloader or boot configuration, which can start an older kernel or fail to boot. To prevent this, sync the contents of the mounted ESP to the other ESPs after each bootloader update, as described in Manage Software RAID (UEFI boot mode) on Dedicated Servers.

With this layout, lsblk -f shows a vfat partition labelled EFI_SYSPART on each disk, and only one of them mounted on /boot/efi, as on this Debian 12 server:

$ lsblk -f
NAME    FSTYPE            FSVER            LABEL       UUID                                 FSAVAIL FSUSE% MOUNTPOINTS
sda
├─sda1  vfat              FAT16            EFI_SYSPART 3080-06E7                             504.7M     1% /boot/efi
├─sda2  linux_raid_member 1.2              md2         37d67f91-25a1-6852-2764-b80ccc46b85a
│ └─md2 ext4              1.0              boot        17e70776-ef0c-4455-b1fa-683d246a21b9  848.4M     7% /boot
├─sda3  linux_raid_member 1.2              md3         d1ad5a59-c32f-f164-4f15-ca4799820c08
│ └─md3 ext4              1.0              root        3e641163-ab2b-4275-9f46-14cffae49540  387.4G     0% /
├─sda4  swap              1                swap-sda4   fae5b711-0373-4ac6-bdec-ac692b4ad82d                [SWAP]
└─sda5  iso9660           Joliet Extension config-2    2026-11-03-18-08-27-00
sdb
├─sdb1  vfat              FAT16            EFI_SYSPART 3095-C236
├─sdb2  linux_raid_member 1.2              md2         37d67f91-25a1-6852-2764-b80ccc46b85a
│ └─md2 ext4              1.0              boot        17e70776-ef0c-4455-b1fa-683d246a21b9  848.4M     7% /boot
├─sdb3  linux_raid_member 1.2              md3         d1ad5a59-c32f-f164-4f15-ca4799820c08
│ └─md3 ext4              1.0              root        3e641163-ab2b-4275-9f46-14cffae49540  387.4G     0% /
└─sdb4  swap              1                swap-sdb4   590ba38f-bacd-460d-8d34-91c1d8499b2b                [SWAP]

One ESP over RAID1

This layout, used by the newer Linux operating systems (see Availability by operating system), is the more reliable of the two. The ESPs of all the installation disks form a software RAID1 array, md1, and the FAT filesystem is created on the array. /boot/efi is mounted from md1, so every bootloader update is written to all the disks.

The array uses the RAID metadata version 0.90, which is stored at the end of each member partition. This way, the UEFI firmware, which does not know about software RAID, reads each member as a normal FAT filesystem. Once Linux has started, it assembles md1 and keeps the members in sync.

With this layout, lsblk -f shows the ESP of each disk as a linux_raid_member, and /boot/efi mounted from md1, as on this Debian 13 server:

$ lsblk -f
NAME    FSTYPE            FSVER            LABEL       UUID                                 FSAVAIL FSUSE% MOUNTPOINTS
sda
├─sda1  linux_raid_member 0.90.0                       fbb410d2-eed5-8b9c-0edd-9cfbcf09b877
│ └─md1 vfat              FAT16            EFI_SYSPART 20B8-687C                             510.5M     0% /boot/efi
├─sda2  linux_raid_member 1.2              md2         6ef065ad-16e9-52ad-384c-94e574f41f0e
│ └─md2 ext4              1.0              boot        5d8c496e-5aed-4f04-a8a4-2a4690b7e556  840.5M     8% /boot
├─sda3  linux_raid_member 1.2              md3         c7110db8-4597-ab47-5f18-3d7634ff3347
│ └─md3 ext4              1.0              root        f97ca283-2a1e-4222-80a6-6abcd22f5d5d  387.6G     0% /
├─sda4  swap              1                swap-sda4   a828894f-c367-439c-bb63-c4dd9e967faa                [SWAP]
└─sda5  iso9660           Joliet Extension config-2    2026-11-03-15-24-14-00
sdb
├─sdb1  linux_raid_member 0.90.0                       fbb410d2-eed5-8b9c-0edd-9cfbcf09b877
│ └─md1 vfat              FAT16            EFI_SYSPART 20B8-687C                             510.5M     0% /boot/efi
├─sdb2  linux_raid_member 1.2              md2         6ef065ad-16e9-52ad-384c-94e574f41f0e
│ └─md2 ext4              1.0              boot        5d8c496e-5aed-4f04-a8a4-2a4690b7e556  840.5M     8% /boot
├─sdb3  linux_raid_member 1.2              md3         c7110db8-4597-ab47-5f18-3d7634ff3347
│ └─md3 ext4              1.0              root        f97ca283-2a1e-4222-80a6-6abcd22f5d5d  387.6G     0% /
└─sdb4  swap              1                swap-sdb4   198999e8-1150-46e9-a342-4c84ca48aa61                [SWAP]

Availability by operating system

The installation creates the ESP on top of RAID1 on:

  • AlmaLinux 10 and newer
  • Debian 13 and newer
  • Fedora 43 and newer
  • Proxmox Backup Server 4 and newer
  • Proxmox Virtual Environment 9 and newer
  • Rocky Linux 10 and newer
  • SUSE Linux Enterprise Server for SAP Applications 15 SP4 and newer
  • Ubuntu Server 26.04 and newer

The installation creates one ESP per disk on:

  • AlmaLinux 8 and 9
  • Debian 12
  • Rocky Linux 8 and 9
  • Ubuntu Server 20.04, 22.04 and 24.04, which has a built-in mechanism to keep multiple ESPs in sync: the grub-efi/install_devices debconf setting of the grub-efi-amd64 package
  • Bring Your Own Linux: the bootloader is installed by the make_image_bootable.sh script of your image, which OVHcloud does not control, so the installation cannot assume that it supports an ESP on top of RAID1

The layout is chosen at installation time and does not change afterwards, even after an in-place upgrade (e.g. Debian 12 → 13).

What the RAID1 layout changes for you

  • You no longer need to sync the contents of the ESPs after bootloader updates, as described in Manage Software RAID (UEFI boot mode) on Dedicated Servers: the RAID1 array writes every change to all the disks.
  • The FAT filesystem keeps the EFI_SYSPART label, so the /boot/efi line of /etc/fstab does not change.
  • Your distribution's bootloader updates work the same way as with one ESP per disk: they write to /boot/efi, and the RAID1 array copies them to every disk.
  • If you run grub-install yourself, add the --no-nvram option. Without it, grub-install tries to create an EFI boot entry for the RAID1 array and fails. In any case, do not change the boot order of your server, as explained in Understanding the dedicated server boot process.
  • After a disk replacement, rebuild md1 like the other RAID arrays. See Manage Software RAID (UEFI boot mode) on Dedicated Servers.

Go further

Understanding the dedicated server boot process

Manage Software RAID (UEFI boot mode) on Dedicated Servers

Hot-Swapping a Disk on Software RAID Dedicated Servers

Join our community of users.

War diese Seite hilfreich?